U-Boot 2013.01.01 (Oct 18 2013 - 18:35:35)
U-Boot code: 80800000 -> 80852768 BSS: -> 80CA4AF0
I2C: ready
monitor len: 004A4AF0
ramsize: 20000000
TLB table from 9fff0000 to 9fff4000
Top of RAM usable for U-Boot at: 9fff0000
Reserving 4754k for U-Boot at: 9fb4b000
Reserving 1152k for malloc() at: 9fa2b000
Reserving 32 Bytes for Board Info at: 9fa2afe0
Reserving 128 Bytes for Global Data at: 9fa2af60
New Stack Pointer is: 9fa2af50
RAM Configuration:
Bank #0: 80000000 512 MiB
relocation Offset is: 1f34b000
WARNING: Caches not enabled
monitor flash len: 0005A990
Now running in RAM - U-Boot at: 9fb4b000
NAND: 512 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - bad CRC, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
mmc_send_cmd : timeout: No status update
Card did not respond to voltage select!
mmc0(part 0) is current device
mmc_send_cmd : timeout: No status update
Card did not respond to voltage select!
Booting from nand ...
NAND read: device 0 offset 0x280000, size 0x500000
5242880 bytes read: OK
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Linux-3.2.0
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3172032 Bytes = 3 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Linux version 3.2.0 (user@linux-developer) (gcc version 4.7.3 20130226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 Fri Oct 18 18:34:05 FET 2013
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: mtax_am335x
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] AM335X ES2.1 (sgx neon )
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyO0,115200n8 root=ubi0:rootfs rw ubi.mtd=7,2048 rootfstype=ubifs rootwait=1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 513220k/513220k available, 11068k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc058f000 (5660 kB)
[ 0.000000] .init : 0xc058f000 - 0xc05c9000 ( 232 kB)
[ 0.000000] .data : 0xc05ca000 - 0xc0631db0 ( 416 kB)
[ 0.000000] .bss : 0xc0631dd4 - 0xc06608e4 ( 187 kB)
[ 0.000000] NR_IRQS:396
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] Total of 128 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz
[ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000061] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
[ 0.089233] pid_max: default: 32768 minimum: 301
[ 0.089324] Security Framework initialized
[ 0.089416] Mount-cache hash table entries: 512
[ 0.089752] CPU: Testing write buffer coherency: ok
[ 0.109130] omap_hwmod: pruss: failed to hardreset
[ 0.110107] print_constraints: dummy:
[ 0.110412] NET: Registered protocol family 16
[ 0.112091] OMAP GPIO hardware version 0.1
[ 0.114105] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.115661] omap_i2c.1: alias fck already exists
[ 0.115814] The board is MTAX-MB in default profile
[ 0.116851] da8xx_lcdc.0: alias fck already exists
[ 0.117645] davinci-mcasp.0: alias fck already exists
[ 0.117950] omap_hsmmc.0: alias fck already exists
[ 0.118133] omap_hsmmc.2: alias fck already exists
[ 0.118499] d_can.1: alias fck already exists
[ 0.119781] omap2_mcspi.1: alias fck already exists
[ 0.119934] omap2_mcspi.2: alias fck already exists
[ 0.120513] edma.0: alias fck already exists
[ 0.120513] edma.0: alias fck already exists
[ 0.120544] edma.0: alias fck already exists
[ 0.140869] bio: create slab at 0
[ 0.142669] SCSI subsystem initialized
[ 0.143981] usbcore: registered new interface driver usbfs
[ 0.144226] usbcore: registered new interface driver hub
[ 0.144378] usbcore: registered new device driver usb
[ 0.144500] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3
[ 0.144744] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1
[ 0.145629] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[ 0.146759] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.147644] Switching to clocksource gp timer
[ 0.159393] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.159576] musb-hdrc musb-hdrc.0: dma type: pio
[ 0.159851] MUSB0 controller's USBSS revision = 4ea20800
[ 0.159881] musb0: Enabled SW babble control
[ 0.160400] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using PIO, IRQ 18
[ 0.160552] musb-hdrc musb-hdrc.1: dma type: pio
[ 0.160797] MUSB1 controller's USBSS revision = 4ea20800
[ 0.160797] musb1: Enabled SW babble control
[ 0.160919] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 0.160980] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
[ 0.161102] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.161102] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.161132] usb usb1: Product: MUSB HDRC host driver
[ 0.161132] usb usb1: Manufacturer: Linux 3.2.0 musb-hcd
[ 0.161132] usb usb1: SerialNumber: musb-hdrc.1
[ 0.161773] hub 1-0:1.0: USB hub found
[ 0.161804] hub 1-0:1.0: 1 port detected
[ 0.162200] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using PIO, IRQ 19
[ 0.162536] NET: Registered protocol family 2
[ 0.162719] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.162963] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.163177] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.163330] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.163330] TCP reno registered
[ 0.163330] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.163360] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.163513] NET: Registered protocol family 1
[ 0.163726] RPC: Registered named UNIX socket transport module.
[ 0.163757] RPC: Registered udp transport module.
[ 0.163757] RPC: Registered tcp transport module.
[ 0.163757] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.163940] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.164154] omap-gpmc omap-gpmc: GPMC revision 6.0
[ 0.164154] Registering NAND on CS0
[ 0.182220] VFS: Disk quotas dquot_6.5.2
[ 0.182281] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.182739] msgmni has been set to 1002
[ 0.185302] alg: No test for stdrng (krng)
[ 0.185882] io scheduler noop registered
[ 0.185882] io scheduler deadline registered
[ 0.185943] io scheduler cfq registered (default)
[ 0.186950] da8xx_lcdc da8xx_lcdc.0: GLCD: Found NHD-3.5-320240MF-ATXL#-1 panel
[ 0.193664] Console: switching to colour frame buffer device 40x30
[ 0.198272] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[ 0.808532] console [ttyO0] enabled
[ 0.812713] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[ 0.820495] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[ 0.828216] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[ 0.835906] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[ 0.843627] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[ 0.858489] brd: module loaded
[ 0.865417] loop: module loaded
[ 0.868896] i2c-core: driver [tsl2550] using legacy suspend method
[ 0.875366] i2c-core: driver [tsl2550] using legacy resume method
[ 0.883819] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 0.891052] omap2-nand driver initializing
[ 0.895690] NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
[ 0.904907] Creating 8 MTD partitions on "omap2-nand.0":
[ 0.910491] 0x000000000000-0x000000020000 : "SPL"
[ 0.916687] 0x000000020000-0x000000040000 : "SPL.backup1"
[ 0.923400] 0x000000040000-0x000000060000 : "SPL.backup2"
[ 0.930053] 0x000000060000-0x000000080000 : "SPL.backup3"
[ 0.936737] 0x000000080000-0x000000260000 : "U-Boot"
[ 0.943725] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 0.950286] 0x000000280000-0x000000780000 : "Kernel"
[ 0.958465] 0x000000780000-0x000020000000 : "File System"
[ 1.172973] OneNAND driver initializing
[ 1.177581] UBI: attaching mtd7 to ubi0
[ 1.181640] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.188201] UBI: logical eraseblock size: 126976 bytes
[ 1.193847] UBI: smallest flash I/O unit: 2048
[ 1.198760] UBI: VID header offset: 2048 (aligned 2048)
[ 1.205047] UBI: data offset: 4096
[ 1.369567] usb 1-1: new high-speed USB device number 2 using musb-hdrc
[ 1.519012] usb 1-1: New USB device found, idVendor=0409, idProduct=005a
[ 1.526031] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.548828] hub 1-1:1.0: USB hub found
[ 1.554107] hub 1-1:1.0: 4 ports detected
[ 1.880767] usb 1-1.4: new low-speed USB device number 3 using musb-hdrc
[ 2.006622] usb 1-1.4: New USB device found, idVendor=13ee, idProduct=0003
[ 2.013824] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.021484] usb 1-1.4: Product: Optical Mouse
[ 2.026031] usb 1-1.4: Manufacturer: MosArt
[ 2.300750] usb 1-1.2: new high-speed USB device number 4 using musb-hdrc
[ 2.429351] usb 1-1.2: New USB device found, idVendor=1bc7, idProduct=0021
[ 2.436553] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.444183] usb 1-1.2: Product: Telit Wireless Module
[ 2.449462] usb 1-1.2: Manufacturer: Telit wireless solutions
[ 2.455474] usb 1-1.2: SerialNumber: 359658044085506
[ 6.626312] UBI: max. sequence number: 130
[ 6.650756] UBI: attached mtd7 to ubi0
[ 6.654693] UBI: MTD device name: "File System"
[ 6.660461] UBI: MTD device size: 504 MiB
[ 6.665649] UBI: number of good PEBs: 4031
[ 6.670562] UBI: number of bad PEBs: 5
[ 6.675201] UBI: number of corrupted PEBs: 0
[ 6.679840] UBI: max. allowed volumes: 128
[ 6.684661] UBI: wear-leveling threshold: 4096
[ 6.689575] UBI: number of internal volumes: 1
[ 6.694213] UBI: number of user volumes: 1
[ 6.698883] UBI: available PEBs: 0
[ 6.703521] UBI: total number of reserved PEBs: 4031
[ 6.708709] UBI: number of PEBs reserved for bad PEB handling: 40
[ 6.715057] UBI: max/mean erase counter: 2/0
[ 6.719543] UBI: image sequence number: 1552853427
[ 6.724731] UBI: background thread "ubi_bgt0d" started, PID 595
[ 6.731048] CAN device driver interface
[ 6.735046] CAN bus driver for Bosch D_CAN controller 1.0
[ 6.741455] d_can d_can.1: device registered (irq=55, irq_obj=56)
[ 6.798309] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
[ 6.804779] davinci_mdio davinci_mdio.0: detected phy mask fffffffe
[ 6.811920] davinci_mdio.0: probed
[ 6.815490] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown
[ 6.822998] PPP generic driver version 2.4.2
[ 6.827789] NET: Registered protocol family 24
[ 6.832702] usbcore: registered new interface driver zd1201
[ 6.838714] usbcore: registered new interface driver cdc_ether
[ 6.844940] usbcore: registered new interface driver cdc_eem
[ 6.851013] usbcore: registered new interface driver dm9601
[ 6.856872] cdc_ncm: 04-Aug-2011
[ 6.860382] usbcore: registered new interface driver cdc_ncm
[ 6.866302] Initializing USB Mass Storage driver...
[ 6.871765] usbcore: registered new interface driver usb-storage
[ 6.878051] USB Mass Storage support registered.
[ 6.883239] mousedev: PS/2 mouse device common for all mice
[ 6.889892] input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input0
[ 6.898315] omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0
[ 6.905487] i2c /dev entries driver
[ 6.909484] Linux video capture interface: v2.00
[ 6.914611] usbcore: registered new interface driver uvcvideo
[ 6.920654] USB Video Class driver (1.1.1)
[ 7.059326] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 7.065826] _regulator_get: deviceless supply vdd_mpu not found, using dummy regulator
[ 7.074493] cpuidle: using governor ladder
[ 7.079162] cpuidle: using governor menu
[ 7.086547] omap4_aes_mod_init: loading AM33X AES driver
[ 7.092254] omap4-aes omap4-aes: AM33X AES hw accel rev: 3.02
[ 7.098937] omap4_aes_probe: probe() done
[ 7.103302] omap4_sham_mod_init: loading AM33X SHA/MD5 driver
[ 7.109466] omap4-sham omap4-sham: AM33X SHA/MD5 hw accel rev: 4.03
[ 7.123077] omap4_sham_probe: probe() done
[ 7.132781] input: MosArt Optical Mouse as /devices/platform/omap/musb-ti81xx/musb-hdrc.1/usb1/1-1/1-1.4/1-1.4:1.0/input/input1
[ 7.145263] generic-usb 0003:13EE:0003.0001: input: USB HID v1.10 Mouse [MosArt Optical Mouse] on usb-musb-hdrc.1-1.4/input0
[ 7.157440] usbcore: registered new interface driver usbhid
[ 7.163299] usbhid: USB HID core driver
[ 7.167907] usbcore: registered new interface driver snd-usb-audio
[ 7.181335] asoc: tlv320aic3x-hifi <-> davinci-mcasp.0 mapping ok
[ 7.188873] ALSA device list:
[ 7.191986] #0: AM335X EVM
[ 7.194976] oprofile: hardware counters not available
[ 7.200286] oprofile: using timer interrupt.
[ 7.204772] nf_conntrack version 0.5.0 (8019 buckets, 32076 max)
[ 7.211547] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.217193] TCP cubic registered
[ 7.220611] NET: Registered protocol family 17
[ 7.225250] can: controller area network core (rev 20090105 abi 8)
[ 7.231842] NET: Registered protocol family 29
[ 7.236480] can: raw protocol (rev 20090105)
[ 7.240966] can: broadcast manager protocol (rev 20090105 t)
[ 7.246917] Registering the dns_resolver key type
[ 7.251892] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 7.259918] ThumbEE CPU extension supported.
[ 7.264434] mux: Failed to setup hwmod io irq -22
[ 7.269958] Power Management for AM33XX family
[ 7.274810] Trying to load am335x-pm-firmware.bin (60 secs timeout)
[ 7.281524] Copied the M3 firmware to UMEM
[ 7.285858] Cortex M3 Firmware Version = 0x181
[ 7.291107] sr_init: platform driver register failed
[ 7.297119] tps65217 1-0024: TPS65217 ID 0xe version 1.2
[ 7.304718] print_constraints: DCDC1: 900 <--> 1500 mV at 1500 mV
[ 7.313201] print_constraints: DCDC2: 900 <--> 1100 mV at 1100 mV
[ 7.321685] print_constraints: DCDC3: 900 <--> 1400 mV at 1325 mV
[ 7.329620] mmc1: new high speed SDIO card at address 0001
[ 7.335937] print_constraints: LDO1: 1000 <--> 1800 mV at 1800 mV
[ 7.344421] print_constraints: LDO2: 1800 <--> 3300 mV at 3300 mV
[ 7.352844] print_constraints: LDO3: 1500 <--> 1800 mV at 1800 mV
[ 7.361297] print_constraints: LDO4: 1800 <--> 3300 mV at 3300 mV
[ 7.371215] registered am33xx_sr device
[ 7.378845] clock: disabling unused clocks to save power
[ 7.394042] Detected MACID=c4:ed:ba:88:e6:16
[ 7.399536] cpsw: Detected MACID = c4:ed:ba:88:e6:18
[ 7.406066] input: gpio-keys as /devices/platform/gpio-keys/input/input2
[ 7.413787] omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 7.504241] UBIFS: recovery needed
[ 7.692443] UBIFS: recovery completed
[ 7.696289] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 7.702575] UBIFS: file system size: 303345664 bytes (296236 KiB, 289 MiB, 2389 LEBs)
[ 7.710937] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 7.718597] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 7.724700] UBIFS: default compressor: lzo
[ 7.728973] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 7.736389] VFS: Mounted root (ubifs filesystem) on device 0:13.
[ 7.743011] Freeing init memory: 232K
INIT: version 2.88 booting
Starting udev
[ 9.983520] Disabling lock debugging due to kernel taint
[ 10.028228] UniFi SDIO Driver: 5.2.1 Oct 18 2013 18:36:59
[ 10.033905] CSR SME with WEXT support
[ 10.037750] Split patch support
[ 10.041015] Kernel 3.2.0
[ 10.043731] UniFi: Using native Linux MMC driver for SDIO.
[ 10.152923] cdc_acm 1-1.2:1.0: This device cannot do calls on its own. It is not a modem.
[ 10.161651] cdc_acm 1-1.2:1.0: ttyACM0: USB ACM device
[ 11.525604] cdc_acm 1-1.2:1.2: This device cannot do calls on its own. It is not a modem.
[ 11.534332] cdc_acm 1-1.2:1.2: ttyACM1: USB ACM device
[ 11.786346] sdio bus_id: mmc1:0001:1 - UniFi card 0x1 inserted
[ 11.879364] cdc_acm 1-1.2:1.4: This device cannot do calls on its own. It is not a modem.
[ 11.888031] cdc_acm 1-1.2:1.4: ttyACM2: USB ACM device
[ 11.895721] cdc_acm 1-1.2:1.6: This device cannot do calls on its own. It is not a modem.
[ 11.904418] cdc_acm 1-1.2:1.6: ttyACM3: USB ACM device
[ 11.916381] cdc_acm 1-1.2:1.8: This device cannot do calls on its own. It is not a modem.
[ 11.925140] cdc_acm 1-1.2:1.8: ttyACM4: USB ACM device
[ 11.944763] unifi: uf_run_unifihelper_cleanup
[ 12.047760] cdc_acm 1-1.2:1.10: This device cannot do calls on its own. It is not a modem.
[ 12.056823] cdc_acm 1-1.2:1.10: ttyACM5: USB ACM device
[ 12.064270] cdc_acm 1-1.2:1.12: This device cannot do calls on its own. It is not a modem.
[ 12.073028] cdc_acm 1-1.2:1.12: ttyACM6: USB ACM device
[ 12.090148] usbcore: registered new interface driver cdc_acm
[ 12.096069] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory
bootlogd.
[ 12.869445] SDIO: Skip power on; card is already powered.
[ 12.875122] unifi1: Initialising UniFi, attempt 1
[ 12.892272] unifi1: Chip ID 0x07 Function 1 Block Size 512 Name UniFi-4(UF60xx)
[ 12.969360] unifi1: Chip Version 0x3A22
[ 12.973419] unifi1: Calling CsrSdioHardReset
[ 12.977874] unifi1: Falling back to software hard reset
[ 12.983367] unifi1: Chip ID 0x07 Function 1 Block Size 512 Name UniFi-4(UF60xx)
[ 13.070190] unifi1: unifi_dl_patch df7a9f48 0100060e
ALSA: Restoring mixer settings...
No state is present for card EVM
Found hardware: "AM335X_EVM" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card EVM
Configuring network interfaces... [ 13.389068] PHY 0:01 not found
udhcpc (v1.20.2) started
[ 13.432861] unifi1: SDIO block size 64 requires 8 padding chunks
[ 13.449157] unifi1: UniFi f/w protocol version 9.1 (driver 9.1)
[ 13.455352] unifi1: Firmware build 1089: 2010-10-05 14:50 cindr03_core_softmac_rom_sdio_gcc 1089 bfsw@eagle@630492
Sending discover...
[ 15.179107] unifi1: 1188199: MAC fault 0022, arg 0006 (x1)
[ 15.282135] unifi1: Firmware patch 1563
[ 15.286682] unifi1: unifi1 is wlan0
[ 15.290405] unifi1: UniFi ready
Sending discover...
Sending discover...
No lease, failing
done.
Tue Jun 25 23:08:00 UTC 2013
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting telnet daemon.
Starting syslogd/klogd: done
Starting thttpd.
Stopping Bootlog daemon: bootlogd.
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org am335x-evm ttyO0
Arago 2013.05 am335x-evm ttyO0
am335x-evm login: root
root@am335x-evm:~#
